November 17, 2026 · 4 min read

Load Bearing Wall Removal Permit Plans: LVL Beam & Post Details

Removing an interior load-bearing wall requires city permits to prevent roof sag or collapse. Here is what your permit drawings must show.

AW

Drafting & Permit Documentation · ArchWorkPro

ArchWorkPro combines AI-assisted drafting with licensed-professional review to deliver permit-ready construction documents for contractors, builders, designers, and homeowners nationwide.

Load Bearing Wall Removal Permit Plans: LVL Beam & Post Details

Why Removing a Load-Bearing Wall Requires a Building Permit

Creating an open-concept living space by removing the wall between a kitchen and living room is one of the most common residential renovation projects in America. Removing that barrier opens sightlines, enhances natural daylight, and dramatically improves home flow.

However, many homeowners and inexperienced remodelers underestimate the structural danger. Unlike non-bearing partition walls (which simply hold drywall and electrical outlets), load-bearing walls support ceiling joists, second-story floors, and roof trusses.

Knocking down a bearing wall without installing an engineered replacement beam causes immediate ceiling sag, binding doors and windows, and potential catastrophic roof collapse. Every municipal building department in the United States strictly requires a building permit and detailed structural CAD drawings before any framing is cut.

The Core Technical Elements Required on Permit Drawings

City plan examiners will not issue an interior remodel permit without detailed structural calculations and framing sheets:

Drawing Element What Plan Review Evaluates Technical Code Requirement
Existing vs. Proposed Framing Plan Wall removal boundaries and tributary load area Identifies joist spans, rafter directions, and load path transfers
Engineered Beam Sizing Depth, width, and material of replacement header Laminated Veneer Lumber (LVL), Glulam, or structural steel I-beam specs
Supporting Post & Column Details Vertical transfer of beam reaction loads Multi-ply 2x4, 2x6, or 4x4/6x6 solid timber posts with Simpson post caps
Point Load Foundation Details Transfer of concentrated post loads into earth Verifying footing width or specifying new concrete pad footings under slab
Temporary Shoring Details Holding up the ceiling during construction Temporary 2x4 stud shoring walls built on both sides of the work area

The most common point of plan check failure is point load transfer. When a continuous 16-foot wall is replaced by a single horizontal beam, the weight that was previously spread across 12 studs is suddenly concentrated onto two end posts. The drawings must demonstrate that the existing subfloor, joists, and concrete foundation slab can carry that concentrated point load without punching through.

Flush Mount Beams vs. Drop Beams

When drafting the permit drawings, the contractor and property owner must choose between two beam installation methods:

  1. Drop Beams (Under Joists): The engineered LVL beam sits directly underneath the ceiling joists. This is the fastest and least expensive method to construct, but it leaves an exposed horizontal beam hanging 8 to 14 inches below the ceiling plane.
  2. Flush Mount Beams (Hidden in Ceiling): The ceiling joists are cut back and hung directly from the sides of the new LVL beam using metal joist hangers (such as Simpson Strong-Tie LUS or HUS hangers). This creates a completely flat, seamless ceiling plane throughout the room, requiring precise CAD hanger schedules.

Professional Engineering Stamp Triggers

Under International Residential Code (IRC) Section R301, standard prescriptive span tables cover simple headers up to specific spans. However, when an interior opening exceeds 10 to 12 feet, or carries two-story gravity loads, municipal plan check departments mandate a structural engineering calculation packet stamped by a state-licensed Professional Engineer (PE).

ArchWorkPro's Structural Remodel Drafting Services

ArchWorkPro provides fast, accurate 2D CAD drafting for general contractors, remodelers, and property owners nationwide:

  • Fixed Transparent Pricing: 2D CAD drafting is priced at $1.00 per square foot of drawn area ($1,200 minimum).
  • Rapid Turnaround: Written quotes returned within 2 working hours; completed plan sets delivered in days.
  • Plan Check Corrections Included: We update CAD drawings at zero additional charge until your city building department approves your permit.
  • Coordinated In-State PE Stamps: When your city mandates structural engineering calculations, ArchWorkPro coordinates licensed PE seals as a transparent separate line item.

Frequently Asked Questions

How do I tell if an interior wall is load-bearing?

Signs of a load-bearing wall include running perpendicular to ceiling joists above, walls positioned directly above basement support beams or foundation walls, or walls that carry roof truss point loads down through the center of the house. A professional drafter or structural engineer must verify before work begins.

Can I use dimensional lumber (2x10 or 2x12) instead of an LVL beam?

For wide openings (12 feet or greater), standard dimensional lumber lacks the structural bending strength and stiffness required. Engineered wood products like Laminated Veneer Lumber (LVL) or steel I-beams provide higher strength-to-depth ratios and resist long-term deflection.

How much do load-bearing wall permit drawings cost?

Traditional architecture firms charge $2,000 to $4,500 to draft structural wall removal plans. With ArchWorkPro's flat rate of $1.00 per square foot, remodel drawing sets cost only our $1,200 project minimum, including beam schedules and connection details.


Planning to remove an interior load-bearing wall? Request a written quote within 2 working hours at ArchWorkPro Get Started or review our service rates at ArchWorkPro Pricing.

Get Your Plans Drafted

$1/sq ft, $1,200 minimum. Delivered in days, with no full-service package required, just the drawings.

Get My Quote →